College of Technology

Computerized Machining Technology Books and Supplies

Textbooks may be purchased at the University Bookstore located at the Pond Student Union - Building #14. Textbooks may also be purchased or reserved on-line through www.efollett.com or the bookstore's website. Save Your Receipts!

Approximate total book and tool costs for this program's options are listed below. Additional book costs will vary depending on the courses taken to fulfill general education requirements for the AAS degree.
Textbooks are subject to change each semester.

I. BOOKS (LISTED BY COURSE) AND SUPPLIES
Description Approximate Price
MACH 0111 Engine Lathe Theory I
Machinery’s Handbook ISBN 08311290025 $95.00
Machine Tool Practices ISBN 01350150871 $137.00
MACH 0112 Machine Math I
Mathematics for Machine Technology ISBN 1428336567 $137.00
MACH 0123 Interpreting Blueprints
Print Reading for Industry ISBN 1605253084 $75.00
MACH 0261 CNC Introduction to Theory
CNC Programming Handbook (W/CD) ISBN 0831133474 $75.00
Calculator – TI-36X or equivalent $18.00
Safety Shoes (Steel Toe required) $30.00
Approximate Total Books and Supplies $567.00

Do not purchase tools until after the first day of class. Vendors will be available in the program.

II. TOOLS, FIRST SESSION (NOTE: tools must be purchased by first week of class)
Quantity Description Approximate Price
1 pair Safety Glasses with side shields OSHA approved, non-prescription $3.00
1 6" X 3/4" Scale in Fractions, 32nds 64ths, 50ths, and 100ths $8.00
6 High speed steel with 5% cobalt lathe bits 3/8" x 3/8" $25.00
1 6 inch caliper - digital or dial type $95.00
1 2 inch paint brush $1.00
1 Dial indicator - 1" minimum travel $15.00
1 Dial test indicator with attachments $125.00
1 10 inch smooth cut file $10.00
1 set 25 piece radius gauge set $40.00
1 Thread center gauge - 60 degree standard $8.00
2 Grease pencils $1.00
1 20 oz. Dead Blow Hammer $15.00
1 Magnetic indicator base with attachments $30.00
1 Micrometer - 0-1" (Vernier Reading to 4th decimal place) $110.00
1 Micrometer - 1-2" (Vernier Reading to 4th decimal place) $125.00
1 Micrometer - 2-3" (Vernier Reading to 4th decimal place) $170.00
1 Depth Micrometer - 0-6" $240.00
1 # 3 Center Drill $5.00
1 #4 Center Drill $8.00
1 6 inch triangular taper file $7.50
1 set 6 piece adjustable parallels $160.00
1 6 inch pliers $8.00
1 set Screwdrivers - Regular and Phillips $9.00
1 Scriber $6.00
1 Tape measure $8.00
1 set Thread wires $21.00
1 Mighty Mag Way Magnetic Base $15.00
1 Wrench, Adjustable - 12" $15.00
1 Telescoping Gauge – 4 piece set $100.00
1 Wrench, Hex Key - 1/32" to 3/8" $9.00
1 Wrench, Hex Key Metric 2-8 $8.00
  Approximate Total Tools Needed for First Session $ 1,448.50
III. TOOLS, SECOND SESSION (NOTE: tools must be purchased by first week of class)
Quantity Description Approximate Price
1 110 piece drill set $180.00
1 pair Tool Box - Top Box $250.00
1 Cabinet - Roller $425.00
2 each Clamps, cantilever (1 inch, 2 inch and 3 inch) $25.00
1 set Swiss pattern files $12.00
1 10 oz. Ball Pein Hammer $15.00
1 Half round indicator clamp holder $35.00
1 Sharpening Stone (Arkansas Hard) - Approximately 4" x ½" x ½" square $5.00
1 Sharpening Stone (Arkansas Medium) - Approximately 4" x ½" diameter round $8.00
1 Offset edge finder $22.00
1 Tap guide $10.00
1 Square Combination Set (4 piece set) $200.00
1 Wrench, Box end - 3/4" $8.00
  Approximate Total Tools Needed for Second Session $ 1,367.00
IV. OTHER EXPENSES
Description Approximate Price
Class fees* for MACH 0110, 0120, 0130, 0140, 0250, 0265, 0270, 0290
(50.00 each)
$400.00
Graduation Application fee for first Certificate/Degree $20.00
Optional fee for any additional Certificate/Degree ($10.00)
Approximate Total Other Expenses
$420.00

*Class Fees will be used to pay for required assessment testing for students, and for MasterCAM software license, computer paper, ink cartridges, metal, and equipment.

Approximate Total Books & Tools - Machining Technology   $3,382.50

ISU tuition and insurance is not included in the above listed fees.
Anticipate additional expenses associated with this program:
Textbooks associated with academic courses,
Transportation, parking, child care, housing.
You must check your class schedule to determine textbooks required by instructor